Home > Windows Update > Computer Freezes During Startup After SP2 Install

Computer Freezes During Startup After SP2 Install

Contents

Helpful +1 Report al tayeb Jul 21, 2010 at 01:27 AM hi some times this may happen cuz of bad settings of the graphic card, if so you have to enter Also tried booting/reinstalling from W7 disc with same problem.Fix #2Powered off computer. After having read another post about which files are used to control USB, I used another old old old PC that was in XP2. In the "Default Monitor ... my review here

If you have a dual-boot or multiple-boot system, use the arrow keys to select the installation that you want to access, and then press ENTER. restart computer after saving the cmos setting. Step 7 contains a reference to the article. Correct the mispositioning with the controls on the monitor. https://www.lifewire.com/when-windows-update-gets-stuck-or-frozen-2624439

What To Do If Your Computer Is Stuck Updating

Your computer may also have come with a program that can make a Windows XP Home Edition disk. Knowledge base article 873148 (with some additional notes inline and after): [Begin of obsolete KB article] You receive an "Access is denied" error message when you try to install Windows XP USB, Firewire Some problems have been seen on some computers with certain USB devices or Firewire disks attached. You can do this even while you still have the error message on your screen.

Still, if Windows XP freezes at startup, the problem may be with the BIOS, which you will need to reset. Boot from the Windows XP install CD, select the Recovery Console. You can identify the point (driver/DLL) where your computer is freezing. Windows Update Stuck Checking For Updates After adding the /NoExecute=AlwaysOff switch in boot.ini the computer was dead stable.

Here it is: fixdb.bat For other possible solutions check http://www.updatexp.com/cryptographic-service.html and the following Microsoft Knowledge Base article for details. What Happens If You Turn Off Computer During Windows Update If it doesn't, or even if it does, but you cannot find any other possible cause, do a repair installation. Einstein Manifolds in dimension five? About Bright Hub Contact Us Advertise With Us RSS Site Map Terms of Use Privacy Policy Copyright Policy ©2012-2016 Bright Hub Inc.

and where do's the dvd player go ??? Windows Update Stuck Installing by R. Is there any way to push it back to last restore point or fix the registry? MANUALLY COPIED USB FILES INTO %SYSTEMROOT%\SYSTEM32 FROM SERVICE PACK.

What Happens If You Turn Off Computer During Windows Update

If the difference is significant, you may consider replacing RAM to avoid Windows XP freezing during startup. anchor By now you should see your desk top in safe mode. What To Do If Your Computer Is Stuck Updating If you cannot boot into Safe Mode or you don't get the Recovery options, go to next section. Please Do Not Power Off Or Unplug Your Machine Installing Update Stuck By now you should see your desk top in safe mode.

If yes, take it out. There are conflicting reports about version 4303. Again, I found another forum where it explained how to get around that. This also reenables ping responses and allows the browser service to start. What Happens If You Shut Down During A Windows 10 Update

The LPR protocol uses TCP Port 515, which is, by default, blocked by the firewall. rickytlcAug 1, 2010, 7:47 AM Had the same issue as u guys with windows 7 hanging on boot. If you just installed Service Pack 2 or a later service pack and have the problem since then, try also to uninstall the network adapter driver, reboot, then let Windows (PnP) The problem here is that it is not certain whether these access rights are not overly permissive and increase other risks, but if all else fails, this may still be better

rwpritchettNov 18, 2009, 10:11 PM Are your hard drives in AHCI or IDE mode? Windows Update Stuck Windows 10 How to create a slipstream CD A slipstream CD means a Windows XP installation CD with Service Pack 2 already integrated. Computer does not work properly with Service Pack 2 Problem may not be related to Service Pack 2 If the problem you experience has been there before installing Service Pack 2

Ordering the service pack on a CD Windows XP SP2 CD order point: http://www.microsoft.com/windowsxp/downloads/updates/sp2/cdorder/en_us/default.mspx Preparing for installation Service Pack 2 does not require any particular preparation, but it is recommended to

rwpritchettNov 17, 2009, 10:48 PM I had a similar problem, though the freeze at the "starting windows" screen would go on to load windows after 1-2 minutes.The problem for me was I then tried to copy over the files with the ones on the USB key. Network connections missing Possible symptoms: The LAN or High-Speed Internet connection icon is missing. Cleaning Up Do Not Turn Off Your Computer it is windows xp home edition.

CD Drive (it was an old crappy one, only played cd's)3. You receive the following error message: Service Pack setup has failed. If you log on as an administrator, you must first start Windows XP Home Edition in Safe mode. If I can save just one person the agony I am going through I will have made the world a better place. :-) StentorianNov 19, 2009, 10:46 AM Okay, new piece

The Windows Installation wizard will appear. Now follow the procedure described in the following Microsoft Knowledge Base article. A clean install involves completely erasing the hard drive that Windows is installed on and then installing Windows again from scratch on that same drive.Obviously you don't want to do this If this is not enough, use the Windows Network Problem Solver.

Despite these issues, networking continues to function correctly, and the ipconfig command still shows all connection and all adapter information. Resetting BIOS/CMOS a terrible idea? Right-click on the hard disk in Windows Explorer, select Properties, Tools, Check disk for errors. Please do not power off or unplug your machine.

Adware T.V. If yes, you have fixed the issue, else proceed to the next step. Found my old XP pro install discs and am able to install XP.Windows 7 just doesn't like my setup, which is really strange because what I have is not out of On a computer that is configured to start to multiple operating systems, you can press F8 when you see the Startup menu.

There are three ways to proceed. Last night I tried with one HDD only in both IDE and AHCI.Hardware build took ~3 hours and booted to bios without a hitch. A quick way to enable Guest network access is to type the following command at a command prompt: net user guest /active:yes Background information: As long as the Guest account is When you are on the "boot" heading press enter bar, this will put you in the boot menu.Then you can use your UP\Down keys to go to your CD,and hit either

Make sure all required services are running. Because you used the registry file that the Setup program created, this registry does not know that these restore points exist and are available. If you are using Windows XP Home Edition, you can log on as an administrative user. Richy Helpful +2 Report RAGHAV Dec 17, 2008 at 11:54 PM WHY XP INSTALLATION STRUDK OFF AFTER COPYING ALL FILES AT THE TIME XP LOGO.MY COMPUTER HAVING 2.4 CELERON PROCEESSOR AND